Skip to content
Back to the blog

How to Sharpen an Axe: File, Stone, and Strop in the Right Order

How to Sharpen an Axe: File, Stone, and Strop in the Right Order-Appalachian Outfitters

To sharpen an axe, clean the head, use a mill file to restore the bevel, a sharpening stone from coarse to fine to refine the edge, and a leather strop to finish. Work one side at a time, remove the burr with alternating passes, and test sharpness when done.

A dull axe is not just frustrating - it is genuinely more dangerous than a sharp one. When the blade fails to bite cleanly, you compensate with extra force, and that is where accidents happen. Learning how to sharpen an axe at home is straightforward when you have the right tools, a stable work surface, and a safe sharpening technique,

What Tools You Need and When to Use Each

The tools required depend on how dull or damaged the edge is. Not every sharpening session starts at the same point, and starting in the wrong place wastes time.

Edge Condition

Start Here

Why

Nicks, chips, or very dull

Mill file

Removes damaged metal and re-establishes the bevel

Dull but undamaged

Coarse sharpening stone

Faster than filing when geometry is intact

Slightly dull, just needs a touch-up

Fine sharpening stone

Refines an edge that is mostly there

Sharp but not fully refined

Leather strop

Aligns the apex and removes the last micro-burr

If the edge has visible damage, start with the file. If the geometry is sound but the axe has lost its bite, go straight to the stone. A strop finishes any session that aims for a clean, reliable edge. You do not always need all three tools - let the condition of the edge guide you.

Mill file, sharpening stone and leather strop used for different stages of axe sharpening

Safety Before You Start

Wear cut-resistant gloves whenever a file or stone is working near an exposed axe edge. A file slip toward a partially sharpened edge is not a minor inconvenience. Clamp the axe head in a vise if one is available, or brace it securely against a fixed surface with the edge facing away from you. Keep your free hand behind the direction of the file stroke, never in front of it.

Find axe sharpening tools and accessories including files, stones, and strops at Appalachian Outfitters.

How to Sharpen an Axe with a File

Filing is the stage that handles geometry and damage. If the edge has nicks, rolls, or has been sharpened incorrectly over time, learning how to sharpen an axe with a file is what corrects it before any stone work begins.

Step 1: Clean and Inspect the Head

Remove any sap, dirt, or light rust from the axe head before touching a file to it. A wire brush handles surface rust; mineral spirits or rubbing alcohol clear sap without damaging the steel. Once clean, examine the edge closely for chips, rolled sections, or uneven bevel angles. Note where damage is most concentrated, as that area needs extra file work before the rest of the edge. While you are at it, check the axe handle for cracks or looseness - a compromised handle is a safety issue regardless of how sharp the edge is.

Step 2: Read the Existing Bevel

Knowing what angle to sharpen an axe at starts with examining the existing bevel rather than choosing a standard angle. Lay the file against the bevel face and adjust its position until it sits flush with the surface. This helps you maintain the original cutting profile as you sharpen. Although many camp axes and felling axes have bevel angles in the 20–25-degree range, the ideal angle depends on the axe's design and intended use. Following the existing bevel is generally more reliable than imposing a new angle, unless the edge requires significant repair.

Mill file aligned with the existing bevel of an axe blade to maintain its sharpening angle

If you're comparing axe designs and edge profiles, explore the range of Gränsfors Bruk axes.

Step 3: File One Side with Forward Strokes

Set the file against the bevel and push it forward in smooth, consistent strokes from heel to toe of the blade. Use light to moderate pressure and push only - never drag the file backward across the edge. Most axes have a curved bit, so roll your wrist slightly as you move from heel to toe to maintain contact with the full arc of the bevel rather than cutting a flat facet. Lift and reset rather than reversing direction.

Step 4: Flip and Match the Other Side

After completing one side, flip the axe and repeat the same number of strokes on the opposite side using the same angle and technique. Matching strokes on both sides keeps the cutting edge centered on the axe body. An edge filed heavier on one side will pull in that direction and produce an uneven bite.

Step 5: Check for the Burr

Run your thumb lightly across the edge from the side that received the last filing, perpendicular to the blade, not along it. A thin rough ridge of metal on the opposite side is the burr, and it confirms the file has reached the apex. Once the burr is present across the full length of the edge, the filing stage is complete.

How to Sharpen an Axe with a Sharpening Stone

Once the file has done its work, learning how to sharpen an axe with a stone is what removes the coarse file scratches, refines the bevel, and brings the edge to actual cutting sharpness.

Step 1: Lubricate the Stone

A few drops of honing oil on an oil stone, or water on a water stone, prevents metal filings from loading the surface. A loaded stone cuts less consistently and slows the work. Apply a small amount and reapply as needed. A dry pass or two is fine for quick touch-ups, but a full sharpening session benefits from consistent lubrication throughout.

Step 2: Work from Coarse to Fine

Hold the stone against the bevel at your established angle and move it in circular or oval motions along the full length of the blade from heel to toe. On a curved bit, keep the stone in contact with the full arc as you move. Start on the coarse side and complete both sides before switching to the fine side. Coarse removes file marks and abrades the bevel; fine refines the surface and begins polishing the edge. Equal passes on each side keep the apex centered.

Sharpening stone applied to an axe bevel during coarse-to-fine edge refinement

Step 3: Remove the Burr with Alternating Passes

Once both sides are worked on the fine side, make several single, light alternating passes to knock the burr off the apex. These passes should be significantly lighter than the sharpening strokes. When the edge no longer feels rough on either side, the stone stage is done.

The Finishing Step Most Guides Skip: Stropping

A leather strop is the step that takes an axe from sharp to genuinely refined, and it is the stage almost every sharpening guide leaves out entirely.

Leather strop used to refine both sides of an axe edge with the spine leading

After stone work, a small residual burr often remains even after alternating passes, and the edge apex may have tiny misalignments that reduce cutting performance and sharpness retention. A leather strop loaded with honing compound, or used plain, realigns these micro-irregularities and removes the last trace of the burr without removing any meaningful amount of steel. Draw the edge along the strop spine-first, in the same direction as the stone passes, and repeat on both sides. Five to ten passes per side is typically sufficient. The result is an edge that shaves cleanly and holds that sharpness noticeably longer than a stone-only finish.

Browse our full selection of camping axes at Appalachian Outfitters.

How to Test If the Edge Is Sharp Enough

Once sharpening is done, a quick check confirms whether the work is finished or whether another round of stone passes is needed.

The Thumbnail Test

Hold your thumbnail at 90 degrees to the edge and let the edge rest on it lightly without pressing. A sharp edge bites and does not slide. A dull edge slides across the nail surface without catching. This is the fastest field check and takes about two seconds.

The Paper Test

Hold a piece of paper vertically and draw the edge through it from heel to toe under light pressure. A sharp edge cuts cleanly with no tearing or dragging. Irregular cuts in a specific section indicate an uneven edge that needs additional stone work in that exact area. This test also reveals any spots the file did not fully address.

The Arm Hair Test

Draw the edge lightly across the back of your forearm without pressing. A sharp axe shaves a clean path through arm hair with minimal contact. This level is the practical goal for a camp axe intended for clean, efficient cutting. Reaching it consistently confirms the full file, stone, and strop sequence worked as intended.

How Often Should You Sharpen an Axe?

There is no fixed schedule for sharpening. The condition of the edge after each session is a more reliable guide than any time interval or use count.

Light use on softwood - splitting pine rounds, processing kindling - may leave the edge in good condition after a full camping trip. Hard use on dense hardwood, wood with grit or dirt embedded in it, or any contact with soil or gravel will dull the edge much more quickly. A useful habit is to run the thumbnail test at the end of each use session. If the edge slides rather than catches, it is ready for a stone touch-up before the next trip. 

Reserve the file for sessions where the thumbnail test reveals chips, rolled sections, or damage the stone cannot address efficiently. Axes from brands like Hults Bruk axe, which use quality high-carbon steel, hold an edge longer between full sharpening sessions.

Close-up of the Hults Bruk Getå Forest Axe showing the stamped axe head and wooden handle against a white background.

If you're choosing an axe for your next outdoor trip, read our guide on how to choose the right axe size for camping to find a suitable option for your needs.

FAQ: How to Sharpen an Axe

What is the best way to sharpen an axe?

A mill file, sharpening stone, and leather strop used in sequence is the most reliable method. The file addresses damage and geometry, the stone refines the edge from coarse to fine, and the strop finishes it. Start at whichever stage matches your edge condition.

What angle should I use when sharpening an axe?

Match the existing bevel on your axe rather than applying an arbitrary number. Most felling and camp axes fall in the 20 to 25 degree range, but the reliable approach is to follow the established bevel with your file or stone and maintain that angle consistently.

Can I sharpen an axe without a file?

Yes, if the edge is dull but undamaged. Start on the coarse side of a sharpening stone and work through to fine. A file is only necessary when there are chips, nicks, or geometry problems the stone cannot address efficiently on its own.

Should I sharpen both sides of an axe equally?

Yes. Equal strokes on both sides keep the cutting edge centered on the axe body. Heavy filing or stoning on one side shifts the apex off-center, which affects chopping and splitting performance. Count strokes or alternate sides frequently to stay balanced.

How long does it take to sharpen an axe?

A routine stone touch-up takes 5 to 10 minutes. A full file-and-stone sharpening on a dull or damaged edge typically takes 30 to 45 minutes. A severely neglected axe may take longer depending on how much material needs to be removed.

Conclusion

Knowing how to sharpen an axe well is the difference between a tool that works with you and one you are constantly fighting. The file corrects, the stone refines, and the strop finishes. Match the starting point to the condition of your edge, keep a sheath on the blade between uses, and run a quick thumbnail check after every session to stay ahead of the work.

Get the next post in your inbox

Gear advice and store news from Appalachian Outfitters. No spam, and you can unsubscribe any time.